Stage Plot and Input List Template for Bands: Plan Your Live Setup Before Every Gig
stage plotsinput listslive soundbandsgig planning

Stage Plot and Input List Template for Bands: Plan Your Live Setup Before Every Gig

mmusicstore.live Editorial Team
2026-11-09
8 min read

Build an accurate stage plot and input list with channel, monitor, backline, wireless, and pre-show checklists for every gig.

A clear stage plot and input list gives a venue or sound engineer the information needed to prepare microphones, channels, monitors, power, and backline before your band arrives. Use the templates and checkpoints below to document your live setup, reduce avoidable surprises, and update the file whenever your lineup or gear changes.

Overview

A stage plot is a top-down map of the stage. It shows where each performer stands or sits, where instruments and amplifiers are placed, which direction performers face, and where power, monitors, microphones, and other equipment may be needed. An input list, sometimes called a channel list, tells the engineer what each mixer channel carries and how that source connects to the sound system.

These documents work together. The plot answers, “Where does everything go?” The input list answers, “What is each source, and how should it reach the console?” Sending both in advance helps the production team estimate channel count, microphone requirements, monitor needs, stage space, and setup time.

Keep the documents accurate rather than impressive. A simple one-page drawing and a readable table are more useful than a detailed graphic that no longer matches the show. Label every performer by role, note equipment that the band is bringing, and identify anything the venue must supply.

What to include in a stage plot

  • Band name, event date, contact person, and current version date.
  • Stage orientation, including “audience” or “front of stage.”
  • Performer positions and names or roles.
  • Instruments, amplifiers, drum kits, keyboards, playback devices, and stands.
  • Vocal and instrument microphone positions.
  • Monitor wedge or in-ear monitor positions and mix numbers.
  • Power requirements and any unusual placement or access needs.
  • Backline supplied by the band versus backline requested from the venue.

What to track

Build one master file for the band, then make a venue-ready version for each show. Track recurring details in the following order.

1. Performer and equipment positions

Draw the stage from the audience’s perspective or use a clear top-down view, but state which convention you used. Mark stage left and stage right if there is any chance of confusion. For each position, identify the musician, instrument, amplifier, stand, and monitor. If a performer moves during the set, show the primary position and add a note such as “moves to center for final song.”

For a solo act, include the vocal microphone, instrument connection, playback or looping device, monitor, instrument stand, and any DI boxes. A duo may need separate positions for two vocals, acoustic or electric instruments, keyboards, percussion, and playback. A full band should show the drum position, bass and guitar amplifiers, keyboard or sampler rig, lead and backing vocals, and any auxiliary percussion.

2. Input list and channel labels

Use one row per console input or source. A practical band input list can use these columns:

Ch.SourceMic or DIStandConnectionNotes
1KickKick microphoneShort boomXLRBand-supplied mic or venue mic
2SnareDynamic microphoneClip or boomXLRConfirm top only or top and bottom
3BassDINoneXLR from DIMic amplifier separately if required
4Lead vocalVocal microphoneStand or handheldXLRWireless or wired; performer supplies capsule if applicable
5Keys L/RStereo DINoneTwo XLR outputsConfirm whether mono operation is acceptable

The sample rows are a format, not a universal channel plan. Replace them with your actual sources. Number channels in the same order used by the sound engineer whenever possible. Use consistent names such as “Lead Vox,” “Bass DI,” “Gtr Amp,” “Keys L,” and “Keys R.” Avoid labels such as “Mike” or “guitar thing” that can create confusion during a fast changeover.

State the expected connection clearly. Common examples include a microphone-level XLR output, a DI box for an instrument or playback device, and two DI channels for a stereo keyboard. Do not assume that a venue has every cable, adapter, stand, or DI box. List what the band brings and what the venue is expected to provide.

3. Monitor mixes and stage communication

Give each monitor position a number and name the person using it. Then describe the priority for that mix rather than requesting “everything.” For example:

  • Mix 1, lead vocal: lead vocal first, acoustic guitar second, kick and snare for timing.
  • Mix 2, drummer: lead vocal, bass, guitar, and click or playback if used.
  • Mix 3, guitarist: lead vocal, own guitar, and enough rhythm section for time.

If the band uses in-ear monitors, note whether the system is wired or wireless, who supplies it, and whether the venue should provide a split or console feed. Include details about ambient microphones or talkback only when they are part of the working setup. For more detail on fit, isolation, and wireless planning, see the in-ear monitors guide for live musicians.

4. Backline, power, and wireless details

Separate backline into three categories: band brings, venue provides, and confirm before show. Include drum kit specifications, cymbals, amplifier models or minimum requirements, keyboard stands, benches, music stands, risers, and specialty items. If a substitute is acceptable, state the minimum workable alternative.

Mark power locations without promising a specific circuit or electrical capacity. Note unusual power supplies, pedalboards, laptop chargers, powered speakers, and equipment that must remain near a performer. Keep mains power and audio-signal routing organized, and ask the venue about safe cable paths and any house requirements.

For wireless microphones, instrument systems, and in-ear monitor transmitters, list the number of systems, the band member using each system, and who is responsible for frequency coordination. Frequencies can be affected by the venue, local requirements, other production systems, and the equipment in use, so do not assign a frequency from an old plot without confirming it with the production contact. Mark wireless systems as “frequency coordination required” when the final assignment is not yet known.

Cadence and checkpoints

Treat the plot and input list as working production documents. A quarterly review is useful for an active band, while a monthly check makes sense during a busy run of shows or when equipment is changing frequently.

When booking or advancing a show

  1. Start with the latest master plot and input list.
  2. Compare the planned lineup with the actual performers.
  3. Confirm stage dimensions, available channels, monitor outputs, microphones, stands, power, and backline.
  4. Ask whether the venue uses a house console, visiting engineer, festival input patch, or shared backline.
  5. Send the current documents with a version date and a contact number.

One week before the show

Reconfirm every item that could affect setup: start and soundcheck times, changeover length, drum and amplifier requirements, wireless coordination, playback connections, and the number of monitor mixes. If your stage plot says “stereo keys,” verify that two suitable inputs are available. If the venue cannot meet the original plan, update the document and share the workaround with every relevant band member.

At load-in and soundcheck

Use the plot as a setup checklist, not as a substitute for communication. Walk the stage, match physical positions to the drawing, identify any changes, and tell the engineer about substitutions before line check. During line check, call sources by the exact channel names used on the input list. Record useful changes, such as a shared vocal microphone, a mono keyboard feed, or a different monitor assignment.

How to interpret changes

Not every change requires a new production plan, but every change should be considered for its effect on channels, stage space, monitoring, and setup time.

ChangeLikely impactUpdate required
New or replacement musicianNew input, monitor mix, stand, and stage positionPlot, input list, monitor notes, and contact details
Instrument changes from mono to stereoAdditional channels and DI outputsInput numbering and connection notes
New wireless systemFrequency coordination, batteries, and receiver placementWireless inventory and production notes
Amplifier moved offstageLonger signal path, isolation, or remote control needsPlot, mic position, DI or line-output notes
Switch from wedges to in-ear monitorsDifferent monitor outputs, feeds, and power needsMonitor plan and equipment responsibilities
Shorter changeoverGreater need for shared stands, prewired inputs, and simple labelingStage plot notes and advance email

When a venue cannot provide the requested setup, choose the smallest change that preserves the performance. A keyboard may run in mono if the player accepts the result; a drum input list may be reduced if the engineer and drummer agree on priorities; a backing-track rig may use a confirmed alternate connection. Record the decision so the band does not rediscover it at the next show.

When to revisit

Review the files at least quarterly and before every important show. Update them immediately after a lineup change, instrument purchase, amplifier move, monitor-system change, new wireless equipment, or change in the band’s playback and effects setup. Also revisit the documents after a venue reports channel, stage-space, power, or setup-time problems.

Use this final pre-show checklist:

  • Is the file labeled with the correct band name, show date, contact, and revision date?
  • Does the stage plot match the physical setup the band will actually bring?
  • Does every sound source appear once in the input list, with no missing vocal, DI, playback, or amplifier channel?
  • Are channel labels, monitor numbers, connection types, and stereo or mono requirements clear?
  • Are band-supplied and venue-supplied items separated?
  • Have wireless systems been identified for coordination rather than copied from an old show?
  • Has the current version been sent to the venue or engineer, and has any exception been confirmed?

Save the master document in an editable format and export a clean PDF for sharing or printing. Keep a show-specific copy after each gig, note what changed, and carry useful corrections into the master file. This simple monthly or quarterly habit turns a stage plot and input list from a one-time form into a reliable live sound tool for every solo set, duo performance, and full-band show.

Related Topics

#stage plots#input lists#live sound#bands#gig planning
m

musicstore.live Editorial Team

Live Sound Editors

Senior editor and content strategist. Writing about technology, design, and the future of digital media. Follow along for deep dives into the industry's moving parts.